Saukewa: GE IS200JPDCG1A

IS200JPDCG1A Hukumar Rarraba Wutar Lantarki ce ta General Electric (GE) ta ƙera don Tsarin Kula da Turbine Gas ɗin Mark VIe™. Wannan hukumar ita ce ginshiƙi na IS2020JPDC Power Rarraba Module, da farko alhakin rarraba 125 V dc, 115/230 V ac, da kuma 28 V dc ikon zuwa sauran allon a cikin tsarin sarrafawa, samar da tsakiya management da kuma rarraba ikon tsarin.

An ɗora allon IS200JPDCG1A akan tushe na karfe a cikin tsarin JPDC. Girman tsarin shine 6.75 inci × 19.0 inci (17.2 cm × 48.26 cm). Jirgin yana haɗa nau'ikan shigarwar wutar lantarki da masu haɗawa da fitarwa, kariyar fuse, jujjuya jujjuyawa, da'irar ra'ayoyin bincike, da wuraren gwaji, samar da cikakkiyar mafita ta rarraba wutar lantarki don tsarin sarrafa Mark VIe.

IS200JPDCG1A kuma daga baya bita ya haɗa da na'urar keɓewar siginar da aka ƙara zuwa hanyar siginar bincike A5 (girman amsa AC1). Wannan yana ba da keɓewar galvanic tsakanin FE/PE da haɗin layin AC JAC. Wannan haɓaka yana haifar da ± 15% haƙuri a cikin karatun siginar amsa AC1 da aka nuna a cikin aikace-aikacen ToolboxST.

Mabuɗin fasalin hukumar IS200JPDCG1A sun haɗa da:

• Rarraba Matsayin Ƙarfin Ƙarfi da yawa: Yana goyan bayan rarraba wutar lantarki don matakan ƙarfin lantarki uku: 125 V dc, 115/230 V ac, da 28V dc.

• Taimakon Shigarwa Mai Sauƙi: Zai iya karɓar abubuwan shigar baturi biyu da shigar da tsarin DACA ɗaya don ƙarfin 125 V dc.

• Taimakon TMR: Yana goyan bayan duka Sau uku Modular Redundant (TMR) da daidaitawa mai sauƙi don ikon 28 V dc.

• Cikakken Kariya: Abubuwan shigarwa da da'irar fitarwa ana kiyaye su ta fuses ko polyfuses.

• Maganganun Ganewa: Yana ba da siginonin gano yanayin ƙarfin ƙarfi ta hanyar fakitin I/O PPDA.

• Abubuwan Gwaji: Yana ba da maki gwaji 8 don dacewa da ma'aunin maɓalli na maɓalli.

• Ƙimar Kanfigareshan Mai Sauƙi: Jumpers suna ba da izini ga daidaitawa don gano ƙasa 125 V dc da 28V dc simplex/m yanayin.

• Fadada Sarkar Daisy: Kebul na ribbon mai 50 yana haɗawa zuwa wasu allunan rarraba don faɗaɗa iya ganewa.

  
  

---

II. Babban Ayyuka

Babban ayyuka na IS200JPDCG1A sun haɗa, amma ba'a iyakance su ba, masu zuwa:

1. 125 V dc Rarraba Wutar Lantarki

Hukumar tana karɓar abubuwan shigar da baturi guda biyu (ta hanyar haɗin JD1 da JD2) da shigarwar 125 V dc ɗaya daga tsarin DACA (ta hanyar haɗin JZ2). Kowace shigarwa ana turawa ta hanyar tacewa ta waje. Abubuwan shigar da baturi guda biyu ana OR'a tare ta hanyar diode module D1 kuma ana OR'ed tare da 125 V dc daga tsarin DACA, suna samar da motar bas 125 V dc mai lakabin PDC. Hanyoyin dawowa na duk abubuwan shigarwar 125 V dc an haɗa su tare kuma ana yiwa lakabin NDC. Jimlar 125V dc na yanzu kada ya wuce 20 amps.

Duk abubuwan shigar 125V dc guda uku suna yawo dangane da ƙasa. Lokacin da aka shigar da jumper JP2, kowane gefen motar 125 V dc bas yana haɗa zuwa ƙasa FE ta hanyar kusan 84 kΩ na juriya, yana samar da hanyar gano kuskuren ƙasa.

2. 115/230 V ac Rarraba Wutar Lantarki

Hukumar tana karɓar shigarwar 115 V ac ko 230 V ac ta hanyar haɗin JAC, tare da matsakaicin izini na yanzu na 12.5 A rms. Ana sa ran ƙasan ƙasa ko tsaka tsaki na ikon shigarwar. Ana samar da abubuwan fitarwa guda biyu na AC, duka suna kiyaye su ta hanyar fuse na jinkirin lokaci 10 A kan babban gefen kawai (Pin 1 na kowane mai haɗawa). Ana sarrafa fitarwa a JAC1 ta hanyar juyawa SWAC1; fitowar JAC2 ba a kunna ba.

3. 28 V dc Rarraba Wutar Lantarki

Hukumar tana goyan bayan rarraba wutar lantarki ta TMR ko simplex 28 V dc. Ana ba da masu haɗin shigarwar 28 V daban-daban, JR, JS, da JT. A kan kowane mai haɗawa, fil biyu suna daidaitawa don ƙara ƙarfin ɗaukan halin yanzu.

• Masu haɗin fitarwa guda takwas waɗanda ba a haɗa su ba: J1, JP1, JCR, JCS, JCT, JRS, JSS, JTS. Fitowar halin yanzu kada ta wuce 12.5 A.

• Fitowa ashirin da shida tare da 1.6 A polyfuse kariya: A cikin tsarin TMR, goma daga cikin waɗannan (JR1-JR10) suna ba da ƙarfin 28PR, takwas suna ba da wutar 28PS, takwas kuma suna ba da wutar 28PT.

• Fitowa ɗaya (P4) tare da 0.5 A polyfuse kariya: Yana iko da fakitin I/O PPDA. A mayar da martani ga overcurrent, da polyfuse latches kashe; ikon sake zagayowar don sake saita shi.

4. 125V dc Fitarwa zuwa Wuta na 125V dc/28V dc Kayan Wuta

Abubuwan da aka fitar JIR, JIS, da JIT suna ba da iko zuwa shigarwar 125V dc na waje guda uku / 28V dc fitarwar wutar lantarki. Waɗannan abubuwan fitarwa ana kiyaye su da fuse kuma ana sarrafa su ta hanyar sauyawa SW1R, SW1S, da SW1T. An bayar da zaɓuɓɓukan zaɓin zaɓin tushen wutar lantarki guda biyu:

• Yanayin Al'ada: Gajeren filogi da aka saka a cikin mai haɗa JDB yana zaɓar ƙarfin 125 V dc daga duk bas ɗin P125 (abincin da shigar da baturi da shigar da DACA ke ciyarwa).

• Madadin Yanayin: Matsar da filogi mai gajarta zuwa mai haɗa JDA yana zaɓar wuta don JIR, JIS, da JIT daga Baturi A kawai, yana barin mai sauya AC/DC mai ƙarancin ƙima don samar da sauran abubuwan 125 V dc kawai.

5. Sauran 125 V dc Fitarwa

• J7A, J7B, J7C Fitarwa: Fuse-kare da sarrafawa ta hanyar jujjuyawar juyawa, suna ba da ikon fitarwa zuwa tashar tashar TRLY Relay Output da kwamitocin makamantansu.

• J8A, J8B, J8C Fitarwa: Fuse-kare kawai, tare da 22 W resistor da aka saka a cikin jeri tare da kowane gefe don iyakance ikon fitarwa. Waɗannan suna ba da wutar lantarki ga allon allo kamar hukumar shigar da Tuntuɓar Sadarwar TBCI, waɗanda ke buƙatar tushen da ke da iyakataccen ikon kewayawa don biyan buƙatun hukuma.

6. Siginonin Ra'ayin Magani

Kwamitin IS200JPDCG1A yana ba da siginar ra'ayin rarraba wutar lantarki zuwa IONet ta fakitin PPDA I/O. Fakitin PPDA I/O yana hawa akan tsarin JPDC. Alamomin ganowa sun haɗa da:

Har ila yau, jawabai sun haɗa da ID na lantarki wanda ke gano nau'in allo, bita, da lambar serial.

7. Abubuwan Gwaji

Kwamitin yana da maki gwajin 8 don dacewa da ma'aunin maɓalli na maɓalli a kan wurin:

Wurin Gwaji	Bayanin
TP1	Layin shigar da AC ACH (ta hanyar 30.1K mai buffer resistor)
TP2	Layin shigar da AC ACL (ta hanyar 30.1K buffer resistor)
TP3	125V dc bas tabbatacce (ta hanyar 30.1K buffer resistor)
TP4	125V dc bas mara kyau (ta hanyar 30.1K buffer resistor)
TP5	Bangaren mara / dawowa na duk abubuwan shigar 28V dc guda uku (babu mai jujjuyawar buffer)
TP6	28PR (28V dc TMR shigar da wutar lantarki tabbatacce R)
Farashin TP7	28PS (28V dc TMR shigar da wutar lantarki tabbatacce S)
Farashin TP8	28PT (28V dc TMR shigar da wutar lantarki tabbatacce T)

---

III. Aikace-aikacen Tsarin

1. Aikace-aikace a cikin Mark VIe Control System

IS200JPDCG1A shine babban kwamiti na rarraba wutar lantarki a cikin tsarin sarrafawa na Mark VIe, yana ba da ƙarfin matakin ƙarfin lantarki da yawa zuwa allunan tsarin. Ayyukansa sun haɗa da:

• Rarraba Wuta ta Tsakiya: Yana rarraba 125 V dc mai shigowa, 115/230 V ac, da 28 V dc ikon zuwa sassa daban-daban na tsarin sarrafawa.

• Sarrafa Wutar Lantarki: Yana goyan bayan shigarwar baturi guda biyu da shigarwar module na DACA, samun wadataccen wutar lantarki ta hanyar dabaru na OR.

• Taimakon Wutar TMR: Yana ba da rarraba wutar lantarki 28 V dc mai zaman kanta don tsarin sau uku na zamani.

• Bincike da Kulawa: Yana ba da amsa matsayin iko ga IONet ta hanyar fakitin PPDA I / O, yana ba da damar saka idanu mai nisa da gano kuskure.

2. Haɗin kai tare da PPDA I/O Pack

Fakitin PPDA I/O yana hawa akan tsarin JPDC kuma yana haɗi zuwa allon IS200JPDCG1A ta hanyar haɗin JA1. Yana da alhakin tattara siginar ra'ayi na rarraba wutar lantarki da watsa su akan IONet zuwa tsarin sarrafawa. A cikin tsarin PDM na tushen JPDC, fakitin PPDA I/O dole ne a saka shi akan JPDC.

3. Fadada Sarkar Daisy

Ta hanyar kebul na kintinkiri 50-pin akan mai haɗa P2, JPDCG1A na iya zama daisy-sarkar da sauran allon rarraba (kamar JPOM). Wannan yana ba da damar siginar bincike daga ƙarin alluna huɗu zuwa JPDC don tattara haɗe-haɗe ta fakitin I/O PPDA. Lokacin da daisy-chained, matsayi na gaba zai kasance ƙungiyoyi biyu mafi girma.

4. Yanayin Aikace-aikace na al'ada

• Tsarin Kula da Turbine na Gas: Yana ba da rarraba wutar lantarki don alluna daban-daban a cikin tsarin sarrafa Mark VIe.

• Tsarin Turbine Control Systems: Ayyukan aiki azaman cibiyar rarraba wutar lantarki, samar da allunan I/O, allon gudu, da sauransu.

• Haɗaɗɗen Shuka wutar lantarki: Yana ba da ikon sarrafa wutar lantarki a tsakiya a cikin DCS ko tsarin sarrafa PLC.

• Sarrafa Turbine Masana'antu: Yana ba da ingantaccen rarraba wutar lantarki don aikace-aikacen sarrafawa mai mahimmanci waɗanda ke buƙatar ƙarin ƙarfi.

  
  

---

IV. Cikakken Bayanin Interface

1. AC Input and Output Connectors

2. 125 V dc Input Connectors

3. 125 V dc Masu Haɗin fitarwa

4. 28 V dc Input and Output Connectors

5. Bincike da Kulawa da Interfaces

6. Juya Sauyawa

7. Wuraren Gwaji

Gwajin	Siginar	Siginar Wuta
TP1	AC shigar da ACH	30.1K jerin resistor
TP2	Shigar da AC ACL	30.1K jerin resistor
TP3	125V dc bas tabbatacce	30.1K jerin resistor
TP4	125V dc bas mara kyau	30.1K jerin resistor
TP5	28V dc yana shigar da dawowar gama gari	Babu
TP6	28PR (28V dc R tabbatacce)	Babu
Farashin TP7	28PS (28V dc S tabbatacce)	Babu
Farashin TP8	28PT (28V dc T tabbatacce)	Babu

---

V. Kanfigareshan da Aiki

1.28 V dc TMR Kanfigareshan

Ana karɓar abubuwan shigar da wutar lantarki na 28 V dc ta hanyar masu haɗawa JR, JS, da JT. An haɗa ingantattun ɓangarorin abubuwan shigar guda uku zuwa keɓance motocin bas ɗin wuta, waɗanda aka keɓe azaman 28PR, 28PS, da 28PT bi da bi. An haɗa ɓangarorin dawowa na abubuwan shigarwa uku tare kuma an tsara su azaman 28N. Ana rarraba wutar lantarki daga bas ɗin guda uku ta hanyar haɗin abubuwan fitarwa na R, S da T daban-daban.

2.28 V dc Simplex Kanfigareshan

Ɗaya, biyu, ko uku 28V dc shigar da wutar lantarki za a iya karɓa ta hanyar haɗin JR, JS, da JT. Ana iya haɗa motocin bas ɗin wutar lantarki guda uku a cikin bas ɗaya ta hanyar saka masu tsalle tsakanin tashoshi 1, 2, da 3 na tashar tashar TB1. Ana ciyar da duk masu haɗin fitarwa daga wannan bas ɗin 28V dc guda ɗaya.

3. Kanfigareshan 125 V dc Fitarwa zuwa Wuta na Wuta

An zaɓi tushen abubuwan fitarwa JIR, JIS, JIT ta matsayin gajeriyar matosai akan JDA da JDB:

• An shigar da JDB: Yanayin al'ada, ikon da aka karɓa daga duka bas ɗin P125 (wanda ake ciyar da shi ta hanyar shigar da baturi da shigarwar DACA).

• An Saka JDA: Madadin yanayin, ikon da aka karɓa daga Baturi A kawai.

Muhimmiyar Gargaɗi: Kada a taɓa haɗa masu haɗin JDA da JDB a lokaci guda!

4. Kanfigareshan Gane Laifin ƙasa

Jumper JP2 yana saita gano kuskuren ƙasa don bas ɗin 125V dc:

• An shigar da JP2: Kowane gefen motar 125 V dc bas an haɗa shi zuwa ƙasa FE ta kusan 84 kΩ resistors, yana ba da hanyar gano kuskuren ƙasa.

• An Cire JP2: Bus ɗin 125 V dc yana iyo game da ƙasa, impedance> 1500 kΩ.

5. Canja Ayyukan Kariya

Lokacin da aka kashe SW1R, SW1S, da SW1T, jira aƙalla daƙiƙa 30 kafin kunna su baya. Wannan yana hana lalacewa ga hanyoyin shigar da kayan wuta na 28V dc.

---

VI. Shigarwa da Sauyawa

1. Wuri Mai hawa

Modulin JPDC yawanci ana hawa a tsaye, tare da mai haɗa shigarwar 115/230 V ac (JAC) a ƙasa. An haɗe shi da sukurori huɗu ta amfani da ramukan hawa da ke sama da ƙasa na tushen tsarin. Allolin rarraba yawanci ana hawa ƙasa kaɗan a cikin majalisar don sauƙaƙe ƙasa.

2. Abubuwan Buƙatun ƙasa

Tsarin sarrafa Mark VIe ya raba ƙasa zuwa Duniya mai Kariya (PE) da Duniya mai Aiki (FE):

• Ground PE: Dole ne a haɗa shi da haɗin ƙasa mai dacewa daidai da duk ƙa'idodin gida. Matsakaicin ƙasa dole ne ya kasance yana iya ɗaukar 60 A na daƙiƙa 60 tare da digo sama da 10 V.

• FE Ground: Dole ne a haɗa shi da tsarin ƙasa na PE a lokaci ɗaya.

FE circuitry a kan hukumar JPDC an kafa shi ta hanyar goyan bayan hawan ƙarfe da aka ɗaure zuwa ƙaƙƙarfan ƙarfe na ƙirar. Jikunan canza ƙarfen da ke kan allo suna ɗaure da kewayar PE. Rarrabe wayoyi na ƙasa daga tsarin JPDC, ta hanyar haɗin gwiwar E5 da/ko E6, dole ne a haɗa su zuwa bas ɗin PE mai shinge.

3. Tsarin Sauyawa

Muhimmiyar Bayani: Don maye gurbin JPDC, maye gurbin gabaɗayan tsarin. KAR a cire allon daga farantinsa mai hawa.

Gargadin Tsaro:

• Kafin maye gurbin allunan tasha, tabbatar da duk hanyoyin Kullewa/Tagout ana bin su.

• Bi da duk alluna tare da dabaru masu mahimmancin kulawa. Saka madauri mai ƙasa da hannu da kuma adana alluna a cikin jakunkuna marasa ƙarfi.

Matakan Maye gurbin:

1. Kullewa/Tagout: Makullewa da/ko bar duk hanyoyin makamashi zuwa tsarin.

2. Tabbatar da Kashe Wuta: Bincika ƙarfin lantarki akan kowane tasha don tabbatar da babu wutar lantarki.

3. Kanfigareshan Rikodi: Lura da fuskantar juzu'in da wurin kowane haɗin da aka yi tsalle. Tabbatar da alamun kuma cire duk masu haɗawa.

4. Cire Wayoyin Ƙasa: Cire kuma cire wayoyi na ƙasa.

5. Cire Hardware na hawa: Cire kayan aikin da aka yi amfani da su don ɗaure tsarin a majalisar.

6. Duba Sabon Module: Bincika sabon tsarin don lalacewar jigilar kaya.

7. Shigar Sabon Module: Shigar da sabon tsarin a cikin majalisar ministoci a daidai wannan tsarin da tsohon tsarin.

8. Tabbatar da Jumpers: Tabbatar da duk haɗin da aka yi tsalle akan sabon tsarin iri ɗaya ne da waɗanda ke kan tsohuwar ƙirar.

9. Sake haɗa Wayoyin Ƙasa: Sake haɗa wayoyi masu saukar da jirgi.

10. Sake haɗa masu haɗawa: Sake haɗa duk masu haɗin waya da na USB.

11. Mayar da Ƙarfi: Cire Kulle/Tagout kuma mayar da iko ga tsarin.

12. Gwajin Aiki: Gwaji/tabbatar da cewa duk masu sauyawa, fuses, LEDs, da fakitin I/O suna aiki da kyau.